Creative Woodworks & crafts 2002-08, страница 28
Bore 1/2"-Pia., centered on a surface to receive the gun barrel continued from page 26 Plan View Drawing Battle Tank With Rotating Turret Turret make one Countersink 3/4"-Dia. x 1/2" deep Bore 1/2"-Dia. x 3/4" deep to receive the pivot pin i L.-^*~Pivot Dowel 5-3/4" ;..........< Bore 1/2" x 3/4" deep, centered, to receive the pivot dowel — --j | [-2"+/--i Bore 7/32"-Pia. thru J. to receive the axle pin 1-1/2" Wheel ||tgfflggggg? ____make seventeen (includes all wheels ____; ! for tank, jeep and howitzer) INSTRUCTIONS Make the parts Size your stock to the dimensions indicated in the supplies list. Referring to the Plan View Drawings cut the various components to shape. It you intend to paint your piece you can certainly use plywood for many of the pieces. Assembly Begin with the Jeep body. First glue the front and rear pieces to the base as shown in the Jeep Assembly Drawing. Next glue the wheel spacers to the lower surface of the base in the locations indicated in the Plan View Drawings. Attach the front and rear wheel wells to the side piece, centered over the wheel spacers. Sand as necessary. Referring to the Rear View Detail Drawing, glue the hitch in place, centered under the rear bumper. Bore the 13/64"-Dia. hole which will receive the spare tire axle pin as shown. Referring to the previous instructions, make the five wheels for the jeep. Glue the seat bottoms to the seat backs (as shown in the Final Assembly Drawing) and install them in the jeep. The angle of the seat backs should be about the same as that of the opening cut into the side pieces. Finishing and final assembly Make sure all surfaces are sanded smooth. Paint the jeep as desired. Install the wheels by gently tapping the axle pins into the 13/64"-Dia. holes as shown in the drawings. I-------3-3/6" ------! I— 2" —4 Gun barrel Glue the gun barrel into the hole in the turret Turret Tank Assembly Drawing Pivot dowel fpj Top piece Laminate the top piece to the bottom piece Note: there will be a 3/4" overlap on both sides. Attach the wheels Wheel Bore 13/64"-Dia. x 3/4" deep to receive the axle pin THE JEEP SUPPLIES Wood: pine or wood of choice—one piece 1 /2" x 3-3/8" x 9" (for the jeep base), two pieces 3/8" x 1-5/8" x 3-3/8" (for the wheel spacers), one piece 1/2" x 1-3/8" x 1-7/8" (for the hitch), two pieces 3/4' x 1-1/4" x 3-1/4" (for the front wheel wells), two pieces 3/4" x 1 -1 /4" x 2- 5/8" (for the rear wheei wells), one piece 3/4" x 3" x 16" (for the wheels), one piece 1-5/8" x 3-3/8" x 3" (for the front piece), one piece 1-5/8" x 3-3/8" x 3" (for the rear piece), one piece MT x 3-3/8" x 9" (for the base), two pieces 3/8" x 1-1/8" x 2-1/8" (for the seat backs), two pieces 3/8" x 1 /2" x 1-1/2" (for the seat bottoms); Baltic birch plywood—two pieces 1 /8" x 2" x 8" (for the side pieces), two pieces 1/8" x 3/4' x 2-1/2" (for the steps) l/4"-Dia. doweling (one piece 1-1/4" long) Five 3/8"-Dia. axle pins Jeep Parts Plan View Drawings 28 • Creative Woodworks S. Crafts August 2002 |
