Popular Woodworking 2007-06 № 162, страница 34

■ Problem No. 2: My bench sways and vibrates when I work, making my saw cuts and attempts at planing into a ragged mess.

Your problem is most likely in the base of the bench. Commercial benches can be too spindly for woodworking. Rebuild the base from massive components and better joints. If you can't do that, stiffen the bench by running all-thread rod through the legs and cinching the base tight with nuts.

■ Problem No. 3: I want a new bench, but I'm low on funds.

Build your bench using Southern yellow pine or fir, both of which are stiff, plentiful and cheap (you can build a bench of your dreams for less than $300, easy). You will have to pick your lumber with care and let it reach equilibrium with your shop. But in the end, you'll have a great bench.

■ Problem No. 4: I think I want a fancy twin-screw vise, Emmert patternmaker's vise or tail vise on my bench. Plus something for working metal.

Before you drop serious coin on vises and put them on every corner, start with a simple face vise. Then buy a tail vise. Then decide after a year of working on the bench if you need the fancier vises. The answer might be yes. You also might forget that you ever wanted those vises.

■ Problem No. 5: My bench is too short in length, too wide, narrow, high or low.

If your bench is too short in length you should probably build a new top. Keep the base if you can. If it's too wide, rip it down (removing a tool tray will help). You might need to cut the base a bit narrower as well. This is doable: Cut the stretchers on the sides shorter and then cut tenons on their ends. Cut new mortises on the legs and assemble it. If your bench is too narrow, scab on new material at the back, which will add mass as well. If your bench is too high, cut down the legs or the sled foot. If it's too low, build a sled foot to raise it.

■ Problem No. 6: My bench makes it difficult to work on the long edges of boards.

First, detach the benchtop from its base and reattach it so the legs are flush

with the front edge of the benchtop. If your bench has a sled foot or a trestle design, there is an easier fix. Scab on extra pieces to the legs to bring them flush with the front of the benchtop. Now build a sliding deadman or a bench slave and you'll be in business.

■ Problem No. 7: My bench looks like a kitchen counter with drawers below. Clamping to the bench is a problem.

You might be stuck here. Some commercial designs allow you to remove the drawer bank (they sell them separately) and you can install it someplace else handy, such as under a table saw's wing. If your bench is a door on top of base cabinets, consider making a new base and use that cabinet as a cabinet.

■ Problem No. 8: My commercial bench came with a face vise and tail vise. Both rack horribly. How do I improve them?

By throwing them in the fireplace and installing a real face vise on the front and tail vise on the end.

■ Problem No. 9: My workbench has a lacquer finish that looks nasty and lets the work slide everywhere.

Flatten the top of your workbench and then refinish the top with an oil/ varnish blend.

■ Problem No. 10: I like my bench in the middle of the room so I can work on all sides.

Perhaps you do. Try putting it under a window and against the wall and work that way for a few months. Don't have a window? Directional compact florescent fixtures can help. Or you can save your pennies and have a window installed. I did. It was the best $1,000 I've ever spent on my shop.

Most workbench books begin with a grand statement about how the workbench is the most useful tool in the shop. I'm not so sure I agree with that statement as it stands. I think it's correct to say that a well-designed, solidly built and properly outfitted bench is the most useful tool in the workshop. Anything less is only making you struggle. PW

Adapted from a forthcoming book by Christopher Schwarz titled: "Workbenches: Design, Construction & Use." Contact Chris at chris. schwarz@fwpubs.com for details on its release.

Everything you need to know about setting up your shop!

From getting the most out of your space, to choosing machinery location, lighting, power and material storage, this seven-chapter series offers all the answers.

Chapter 6 Rules for Workbenches

Beyond machines, workbenches are where everything gets done in a wood-shop. Choose well.

IN FUTURE ISSUES

Chapter 7 Dust Collection

Keep your shop (and your lungs) dust free by planning ahead for any task.

IN PAST ISSUES

Chapter 1 (issuE #157)

The Right Location

Learn the pros and cons of basement, garage and outbuilding shops - and how to make the most of any shop.

Chapter 2 (issuE #158) Lighting & Power

Task versus ambient lighting? 110v or 220v power? Learn the best options for your shop.

Chapter 3 (issuE #159)

Placing

Machinery

The right machines in the right locations will make your woodworking smooth.

Chapter 4 (issuE #160) Small Tool Organization

Balancing maximum storage with accessibility will save time and energy.

Chapter 5 (issuE #161) Material Storage

Proper lumber and sheet-good storage keeps the materials straight and handy.

Order back issues online at popularwoodworking.com or call 800-258-0929.

Popular Woodworking