Woodworker's Journal 1984-8-6, страница 27

SAVE as much as 80% with 3ZL Quality Power Tools

The easiest way to recess for an insert is to first trace the outline of the insert on the "ground," and then rout freehand to within about 1/16 in. of the line. Use the appropriate carving gouge (#3 gouges are ideal) and/or X-acto® knives to trim the remaining wood away.

Routing for inserts may also be accomplished using templates and guide bushings. This procedure involves three basic steps. First, make an exact pattern of the insert on a piece of V* in. plywood or hardboard. Fix this pattern to a second section of V* in. template stock with wire brads. Now, using a V* in. straight bit and a Vi in. guide bushing, cut out the actual template.

Next, locate the template on the "ground," exactly where you want the insert, and clamp the template in place. (It is a good idea to make the template from a large section of template stock to allow room for clamping.) Change to a 1 in. guide bushing and cut the outline of the insert. Finally, clean out the remaining waste (see Fig. 2).

By using this same template guide in conjunction with the V* in. straight bit and Vi in. guide bushing you may cut your own veneer inserts. As an aid in positioning inserts, most experts suggest drawing centerlines across both the veneer and the ground, and marking one edge with an "x".

SCRATCH STOCK

Before electricity and powered routers, much border inlay work was ac-

(continued on next page)

template.

VA" harbroato

CUTTING THE. TEWT-NTE.

routing the recess

fk5ure- 2

B/vse

a ROUNb STOCK

-TEWlPUATe

FANTASTIC VALUES WITH THIS COUPON!

AMERICAN MACHINE & TOOL CO., INC., 4th Ave. & Spring St., Royersford, PA 19468

trail our Royerstartl FACTORY SHOWROOM lor these same low prices. 4tl> and Spring Sis. From 9 10 4:30 on weekdays and 9 to 12 on Sal

INDUSTRIAL SIZE 12 SWING 4 FT.

wood lathe _

Comparable m speed precision and durability lo units selling tor $200 and more. 36"between centers. For wood and plastics Tubular steel bed rails with dual poinl suspension increase accutacy. ease ol operation Precision baU Ihiusl cup center heavy spur cental, graduated T-rest 3-Speed pulley lor different woik diameters Heavy-duly ball-bearing model $79.50.

I.o.b. ladory. Shipping Wl. 30 lbs. Faceplate (optional) lor turning bowls, lamp bases, etc. S4 50. Set ol 3 high Complete as shown speed turning chisels. S11.00 add'l; Set ol 8. SZ9 00.

10-YEAR LIMITEO WARRANTY'

P Turning

. chisels

chisels handcralted to'eiacllno metallurgy standards. Set ot 10 includes two skews, three gouges, parting tool, round nose spear point plus two inside turning tools—all in a wooden storage case s/l A 95 l o b. ladory Wt. 7 lbs.

HI 10-YEAR LIMITED WARRANTY-

KlEW/.' 5V« JOINTER-PLANER

^,195^ma———

Factory ■ ^jN^a^^B

Wl. SO lbs. -B ... —ag^Sgl^BMI

Holds workpiece firmly without screws

Cast iron and sleel chuck -

with-I independent revets- JfeaaA

tbie. stepped black steel JB^^,

jaws Outside diameter

chucking 716 to 5", in- ^

side diameter chucking

7 8 to 6" Fits all AMT wood lathes and others

with headstock spindle tmeaded 3.4" x 16

..... Chuck key included.

oADoll I.o.b. factory Wt. 6 lbs.

"O 10-YEAR LIMITED WARRANTY-

BRAND NEW

Develops a full 1 HP '^^^^BP/

New General Electnc Moior ^^O^Ei^ for use with any po.ver tool in 'fW this ad. Features 1,2" shaft. 1725 RPM $49.50 if purchased with any AMT tool ($54.55 if purchased separately). 17 lbs. f.o.b. factory. Covered by a one year limited warranty.

American Machine & Tool Co.. Oept. wjm

Please send me the units checked L Payment in full enclosed S . S5.00 deposit each item enclosed C O D. or charge my □(" ~

Card No _

. 4th Ave. 4 Spring St.. Royersford, PA 19468

□ 12'Swing. 4 Ft. Lathe 587.75

□ Ball-bearing Model $79.50

□ 4.jaw Laihe Chuck $>6 80 Face Plate S4 50

: Set ol 3 Chisels S11 00 (not shown)

□ Set ol 8 Ctvseis $29 00 (not shown) Master Set ol Turning Chisels $44.95

j Spmdle Shapet Kit $44.00

Expiration Dale _

Signature_

Address_

C 8"Til: Arbor Saw S52.50 D Standard Rip Fence $6.50 _ Long Cabinet Rip Fence S7.50 □ Sali-oeanng " -----

ing Spindle $12.50 t-Planer $t95 00

□ 5ft" Jointer-P H Bell Sander $52 00

□ Disc Sander Attachment $17.00

□ Mitre Gauge for Sander $3.50 General Electnc Motor □ $49 50 (with otner item) "1 $54 55 (puichaseo separately)

. Name_ _City __

-Zip-